Home » Blog » Bubble Light Options – Experimenting With Alcohol Inks And Spray Paints

Bubble Light Options – Experimenting With Alcohol Inks And Spray Paints

My ceiling medallion lastly arrived for the bubble gentle that I’m making in our grasp toilet. So yesterday, I took a while to experiment with completely different finishes for the bubbles (that are Christmas ornaments).

I can’t say that I’ve all of it discovered but, however I can say for positive which choice isn’t going to work. Right here’s what the sunshine seems like in its present state. It’s simply all 4-inch frosted ornaments. I didn’t purchase sufficient, so I needed to place one other order and anticipate these to reach. After which I made a decision so as to add a ceiling medallion, so I’ve been ready on that to reach. However right here’s the final concept…

The brand new ornaments that I ordered had been listed as “clear frosted”. That’s a bit complicated as a result of they will both be clear or frosted, however they will’t actually be each. However I took the “clear” to imply that they had been white. With out coloration. That they had taken clear ornaments and frosted them.

So think about my shock and disappointment when each field regarded like this…

There are 5 white and 4 pink/peach ornaments in each field. However I assumed that the pink/peach ones is perhaps good for me to experiment on. So lots of you instructed that I strive a really gentle pink, and the one approach I may suppose to try this in a approach that may not flip the bulbs opaque is with alcohol ink.

So I attempted all the pink alcohol inks that I had available, and…effectively…it didn’t work out.

Those that look actually splotchy are ones the place I attempted placing just a few drops of alcohol ink immediately onto the bulb, after which pouring a little bit of isopropyl alcohol over it to even out the ink and provides the bulb a wash of coloration. All of them regarded lovely till I turned them over, after which all the ink and alcohol that had collected within the little cap ran down the bulb and created these traces. It was a giant mess.

Those that look somewhat smoother are ones that I attempted to paint by mixing up some alcohol ink diluted with isopropyl alcohol in a bowl, after which rolling the bulb within the coloration wash. Then I used my hair dryer to dry them as shortly as potential to keep away from runs. It labored significantly better, however all of them had at the very least one run on the final facet to dry. And I simply couldn’t get any of the colours to look proper.

So I deserted that concept and headed to Michael’s to see what they may have that might work. I discovered some Mod Podge Iridescent Acrylic Sealer. I used to be excited to strive that out on the bulbs and see simply how they’d look with an iridescent end.

Apparently, right here’s what the spray did to the bulbs.

Isn’t that loopy? It turned them from frosted again into virtually clear. And I really love how they appear. I don’t actually see the iridescent high quality of the spray, although. Right here’s the unique look on the left, and the take care of being sprayed with the iridescent spray on the best.

Out of all three seems — the unique, the alcohol ink (if I may ever get a easy end), and the iridescent spray, those with the spray are my favorites.

They undoubtedly look extra like precise bubbles, however I simply want the iridescent spray regarded extra iridescent.

I suppose you simply should hold spraying to be able to construct up layers of the tiny glittery iridescent particles within the spray, however at that fee, I’d want about 10 cans of the spray to be able to get them to truly look iridescent.

So I simply should determine if it’s value it to spray all of them, or if I ought to simply persist with the medallion and the unique frosted bulbs.

I did spray one of many massive bulbs, and it did the identical factor. It turned it extra clear and glossy. Are you able to see it right here? With out the medallion, it sort of blends proper in to the ceiling. It’s on the left.

And right here it’s on the best. I do actually like that it seems extra like an precise bubble.

I don’t love that it’s extra see via, although.

Anyway, right here’s the medallion that may go on the ceiling. I ordered the vintage brass end, and this isn’t fairly what I imagined vintage brass wanting like. It’s not what the image confirmed.

I imply, it simply has the tiniest little bit of vintage brass end on it, nevertheless it’s largely black.

It’s not an enormous deal. It’s nothing {that a} little bit of spray paint can’t repair. However I do need it to be nearer in coloration to the tap and different plumbing fixtures. (I eliminated the tap handles to make some changes. That’s why you don’t see them there. 🙂 )

In order of proper now, I do suppose I’ll proceed on with the iridescent spray. I simply actually want it was extra iridescent! Any concepts? There’s not a complete lot of iridescent sprays on the market. I believe I discovered possibly two manufacturers, and this one was rated increased than the opposite. All the things else I discovered was a brush-on product, and I actually don’t need that. So how on the earth can I get a delicate iridescent end on these whereas maintaining them translucent sufficient for gentle to shine via? That’s the dilemma, and that’s what I want to determine.

Source link

Leave a Reply

Your email address will not be published. Required fields are marked *